Cordless tool set Combo DCD796+DCF887+DCS355+DCS334+DCH273+DCG405+DCS570, 18V XR, DeWalt [DCK755P3T-QW] 3x5.0Ah, Li-Ion, TStak +

7 DEWALT 18V XR Combo Cordless Tool Kit [DCK755P3T-QW]:

18V XR DEWALT Cordless Drill [DCD796]:

• lightweight impact drill for working with many materials,
• compact 18V impact drill with XR lithium-ion batteries for working in tight spaces,
• 2-speed metal heavy-duty gear increases tool life
• 15-position torque adjustment allows precise work with many materials,
• LED lighting increases the visibility of the workplace and provides the functionality of a flashlight,
• Smart trigger allows you to maintain full control during work,
• improved, ergonomic and rubberized handle improves working comfort,
• The drill has a hanger that allows you to hang the device on a belt and a magnetic holder for holding bits

Technical parameters of the DeWalt drill [DCD796]:

• supply voltage : 18V
• Battery type : lithium ion,
  
• idle speed :
  - 1st gear : 0-550 rpm,
  - 2nd gear : 0-2000 rpm.
• stroke frequency at idle speed :
  - 1st gear : 0-9350 strokes/min.,
  - Gear 2 : 0-34000 cycles/min.,
• maximum steel drilling diameter : 13 mm,
• maximum drilling diameter in the wall : 13 mm,
• maximum drilling diameter in wood : 40 mm,
• maximum soft/hard torque : 27/70 Nm,
• compression range : 1.5-13 mm,
• dimensions : 190 x 203 x 67 mm,
• weight : 1.3 kg

1/4" 18V XR Cordless Impact Driver [DCF887]:

• high-performance brushless motor with up to 205 Nm of torque ensures readiness for even the most difficult assembly tasks,
• a brushless motor has lower energy losses due to less friction - it can run longer on a single battery charge and last much longer,
• very compact design (length only 134 mm) allows you to work freely even in places with limited access,
• 3-speed rotation speed adjustment allows you to accurately select the right parameters for the work being done,
• precision torque mode with electronically adjustable clutch provides additional options for jobs that require control of the torque used to tighten the screw. The clutch works only in the first gear, on the principle of automatic, gradual tightening of the screw - thus avoiding damage to both the screw and the thread,
• the light ring with three LEDs always ensures a very good visibility of the working area,
• the screwdriver has a hex socket for 1/4 inch bits

Impact Drive Parameters [DCF887]:

• supply voltage : 18V,
• Battery type : lithium ion,
• rotation speed in 1st idle gear : 0-1000 rpm.
• rotation speed in 2nd idle gear : 0-2800 rpm.
• rotation speed in 3rd idle gear : 0-3250 rpm.
• impact speed at idle : 0-3800 rpm
• maximum torque : 205 Nm,
• tool holder : 1/4" hex
• dimensions : 134 x 225 mm,
• weight : 1.34 kg

18V CORDLESS MULTI TOOL [DCS355] :

• with the latest brushless motor,
• has a quick-change accessory system,
• perfect for renovation and installation works or processing of various complex materials (fiberglass, hard plastic) and renovation works,
• DUAL-GRIP speed control switch ensures proper speed,
• the accompanying guide allows you to set the cutting depth and make it easier to follow the line,
• ergonomic design with a convenient, large switch with electronic speed control allows easy one-handed operation,
• bright LED lighting ensures excellent visibility of the work area

MULTIFUNCTION TOOL [DCS355] TECHNICAL PARAMETERS:

• supply voltage : 18V,
• Battery type : lithium ion,
• swing speed : 0-20000 rpm.
• dimensions (length) : 310 mm,
• weight (EPTA) : 1.5 kg
  

18V XR Cordless Jigsaw [DCS334]:

• professional cordless jigsaw with a powerful brushless motor,
  
• electronic regulation of rotation speed,
  
• quick change lockable saw blade holder,
• electronic engine brake,
  
• a switch with smooth speed regulation and an activation lock ensures user safety,
• The 4-stage cutting disc tilt function (lowering) allows you to increase the cutting speed or accuracy, depending on the material being processed,
  
• Tool-free adjustable foot with anti-scratch pad, tilts up to 45° in two directions,
• dual leds,
• soft rubber handle

JIG Saw PARAMETERS [DCS334]:

• supply voltage : 18V XR,
• Battery type : lithium ion,
• travel speed without load : 0-3200 strokes/min.
• stroke length : 26 mm,
• maximum angle of deviation from the vertical : 0-45°,
• maximum wood cutting capacity : 135 mm,
• steel cutting range : 10 mm,
• weight : 2.1 kg

CORDLESS DRILL SDS+, 18V XR, [DCH273]:

• designed for drilling in hard concrete with a drill bit up to 24 mm and for light work, such as chipping plaster or tiles,
• 3 working modes: drilling, hammer drilling and hammering,
• The SDS+ system allows you to quickly change drills or chisels,
• is equipped with a brushed DC motor, which significantly increases the efficiency of working with a single battery,
• it has an electronic clutch that allows you to work safely when drilling, especially with larger diameter drills.
• the lowest vibration level in its class of 6.6 m/s ² increases the safety and comfort of working with the tool and allows the operator to work longer,
• depth stop allows you to set the desired drilling depth,
• electropneumatic hammer mechanism ensures high drilling performance and compact size,
• ergonomic design of the handle with a rubberized rear handle, ensuring greater working comfort

HAMMER DRILL [DCH273] PARAMETERS:

• supply voltage : 18V,
• Battery type : lithium ion,
• impact energy (measured according to EPTA 05/2009) : 2.1 J,
• speed without load : 0-1100 rpm.
• beat frequency : 0-4600 bpm,
• maximum drilling diameter in concrete: 24 mm,
• maximum drilling diameter in wood: 26 mm,
• maximum drilling diameter in metal: 13 mm,
• weight : 2.5 kg,
• dimensions : 301 x 202 x 85 mm

CORDLESS ANGLE GRINDER 18V XR [DCG405]:

• Cordless angle grinder for discs with a diameter of 125 mm, for grinding and cutting metal and stone materials without using water,
• 18V brushless DC motor,
• electronic brake - quickly stops the disc when the switch is released,
• electronic clutch reduces kickback when the blade jams or jams,
• mesh-protected air intakes limit the intake of dust into the engine,
• partially rubberized body provides grip and comfort,
• 2-position side handle attachment for added comfort and control

TECHNICAL PARAMETERS OF THE ANGLE GRINDER [DCG405]:

• supply voltage : 18V,
• Battery type : lithium ion,
• idle speed : 9000 rpm,
• disc diameter: 125 mm,
• disc hole diameter: M14,
• dimensions : 310 mm ,
• weight (EPTA) : 1.75 kg

18V XR CORDLESS CIRCULAR SAW [DCS570]:

• with a 184 mm diameter disc with a 16 mm inner bore and 24 teeth,
• durable fan-cooled motor with high power and high torque guarantees fast and safe cutting of various types of wood, plywood or OSB panels,
• the tool-free cutting angle setting and cutting depth adjustment system allows accurate cutting of materials up to 65 mm thick,
• the saw has the ability to set the cut at an angle of up to 57 °,
• has a quick brake that ensures greater work safety,
• durable construction, ergonomic handle

TECHNICAL PARAMETERS of circular saw [DCS570]:

• supply voltage : 18V,
• Battery type : Li-Ion ,
• rotation speed without load : 5500 rpm.
• disc diameter : 184 mm,
• disc hole diameter : 16 mm,
• maximum cutting depth at 90 ° angle : 64 mm,
• maximum cutting depth at 45 ° angle : 49 mm,
• dimensions (length x height) : 355 x 245 mm,
• weight : 3.6 kg

The DEWALT Combo Kit [DCK755P3T-QW] includes:

• DCD796 impact drill ,
• impact driver 1/4" DCF887,
• DCS355 multi-tool,
• Puzzles DCS334,
• drill SDS+ DCH273,
• angle grinder DCG405,
• circular saw DCS570,
• 3 18V XR batteries with a capacity of 5.0 Ah,
• multi-voltage, dual-socket charger DCB1104,
• 3 boxes : TStak II, TStak VI, DWST83347-1 on wheels,
• user manuals

DeWalt has introduced a 3-year European power tool warranty that is valid after registering on the DEWALT website.

PHU A/B/C is an authorized representative of the DeWalt brand and operates an authorized service center.

All DeWalt power tools can be repaired by sending them to our Service Center A/B/C.